Brazing Equipment & Safety Equipment

Shade 4 Clip-on/Flip-up protective spectacles. They must be worn over an approved ANSI Z87.1 safety lens and frame with side shields for severe impact resistance and protection. A minimum of a shade 3 or 4 lens is recommended by OSHA and AWS ANSI/ISEA Z87.1 when brazing.

FREE SHIPPING!

Warning

Misuse of this product may result in serious injury. The clip-on/flip-up lens enclosed within, complies with ANSI Z87.1 to provide protection against ultraviolet, visible or infrared light from soldering or brazing. It is not impact resistant. It is not to be used for gas welding, cutting, electric/arc welding, or any other operation that exposes the wearer to ultraviolet or infrared over the lens shade designation that is inscribed on the flip-up attachment.

The flip-up attachment must be worn over an approved ANSI Z87.1 rated safety lens and frame with side shields for severe impact resistance and protection. Consult with your supervisor or safety manager for proper shade designation.

Shade 5 Clip-on/Flip-up protective spectacles. They must be worn over an approved ANSI Z87.1 safety lens and frame with side shields for severe impact resistance and protection. A minimum of a shade 3 or 4 lens is recommended by OSHA and AWS ANSI/ISEA Z87.1 when brazing.

FREE SHIPPING!

Warning

Misuse of this product may result in serious injury. The clip-on/flip-up lens enclosed within, complies with ANSI Z87.1 to provide protection against ultraviolet, visible or infrared light from soldering or brazing. It is not impact resistant. It is not to be used for gas welding, cutting, electric/arc welding, or any other operation that exposes the wearer to ultraviolet or infrared over the lens shade designation that is inscribed on the flip-up attachment.

The flip-up attachment must be worn over an approved ANSI Z87.1 rated safety lens and frame with side shields for severe impact resistance and protection. Consult with your supervisor or safety manager for proper shade designation.

Flashback arrestors are a combination reverse flow check valve and flame barrier in one body. They provide protection against flashback and the reverse flow of gases to the operator at the torch. 

Specifications

Connection:

• Inlet: 9/16" UNF (CGA Class "B" Connection) M
• Outlet: 9/16" UNF (CGA Class "B" Connection) F
• Part Number: 616226-02070

Flashback arrestors which install easily on the outlet fitting of most regulators and gas supply points. The arrestors meet meet ANSI Z49.1 2005, OSHA, NFPA safety requirements and  protect against the most common causes of accidents such as reverse gas flow, flashback, and hose burn back. Please note this product is for fuel gas.

Specifications

Connection:

• Inlet: 9/16" UNF (CGA Class "B" Connection) F
• Outlet 9/16" UNF (CGA Class "B" Connection) F

Flashback arrestors which install esaily on the outlet fitting of most regulators and gas supply points. The arrestors meet meet ANSI Z49.1 2005, OSHA, NFPA safety requirements and  protect against the most common causes of accidents such as reverse gas flow, flashback, and hose burn back. Please note this product is for oxygen.

Specifications

Connection:

• Inlet: 9/16" UNF (CGA Class "B" Connection) F
• Outlet 9/16" UNF (CGA Class "B" Connection) F

The Lean Ignitor is an electric ignitor for gas brazing torches. The Lean Ignitor eliminates the need for a pilot flame, saving gas.

 It is simply activated by depressing the switch lever with the torch tip.

• Rugged stainless steel construction: 5” x 7” x 5” inches
• Electrical requirements: 120vac 60hz 0.4 amps

• Welding Hose for use with fuel gases including acetlylene
• Flame and Oil resistant tube and cover
• Highly flexible and robust
• Hoses are one continuous length
• Red hose for fuel gas/Green hose for oxygen